The Ultimate Guide to Using Your SOURCE orb 4 Vape Pen

SOURCEvapes Team on
The Ultimate Guide to Using Your SOURCE orb 4 Vape Pen

The Ultimate Guide to Using Your SOURCE orb 4

using source orb 4

If you're looking for a start-up vaporizer to puff concentrate with while on the go, then you've come to the right place! The SOURCE orb 4 offers a wide selection of atomizers you can choose from which makes it a great buy for customers who prefer to change it up every now and then. With its sleek design and portability, the SOURCE orb 4 definitely makes you stand out in a crowd while at the same time providing the discretion you need.

The SOURCE orb 4 kits come with two different batteries. The Premium Kit includes a 650 mAh sub-ohm Premium battery specifically designed to work with our 4 series atomizers. It has 8 voltage settings, easily adjustable at the voltage wheel found at the base of the pen. On the other hand, the Signature Kit comes with the SOURCE volt Max, a battery box mod that is sure to give you powerful hits and an optimum vaping experience.

How to Use Your SOURCE orb 4 Premium Kit

source orb 4 premium kit

Attach Atomizer

Take your SOURCE orb 4 Attachment and screw it onto your SOURCE orb 4 Premium battery.

Remove the magnetic top from the attachment and install your atomizer clockwise on the bottom orb.

Load Material With Your Dab Tool

Using your dab tool, fill your atomizer with the material you'd like to vaporize.

Replace the magnetic top of your SOURCE orb 4.

Select Desired Airflow

Choose your desired airflow by twisting the Variable Airflow System (VAS) found in the middle of the orb.

Adjust Battery Voltage And Power On

Adjust the voltage wheel found at the bottom of your battery to your desired voltage setting.

Press the power button 5 times sequentially to turn it on.

Power Up And Hit It

Press and hold the button for 4 to 7 seconds to pre-heat your atomizer.

Place the mouthpiece on your lips and inhale gently to Experience True Taste.

You can determine the remaining battery capacity by checking the light indicator on the battery when button is pressed:

Blue - 80% - 100%
Pink - 40% - 79%
Red - Less than 40%

You may need to charge your Premium battery before using it the first time. To do this, simply connect the Premium battery to your charger and plug it in. The light on the charger is green by default with nothing connected to it. If your battery needs a charge, the light on the charger turns red once your battery is attached. The light turns back to green once the battery is fully charged, which takes between 2 to 3 hours.

How to Use your SOURCE orb 4 Signature Kit

source orb 4 signature kit

The SOURCE orb 4 Signature Kit includes the SOURCE volt Max, a battery box mod specifically designed for SOURCEvapes products. It offers a full temperature range between 200°F - 700°F, as well as a full wattage control with a range of 5w up to 70w. It also features a removable SONY battery, allowing users to carry extra batteries and quickly replacing on-the-go for extended sessions.

Engage Battery

To use your Signature Kit, first remove the magnetic cover in the back of your SOURCE volt Max and insert an 18650 battery with the Positive + side Up.

Replace the magnetic cover, then press the Power Button sequentially 5 times to power on.

Screw On Attachment and Atomizer

Take your SOURCE orb 4 Attachment and screw it onto your SOURCE Volt Max.

Remove the magnetic top from the attachment and install your atomizer clockwise on the bottom orb.

Load Material With Your Dab Tool

Using your dab tool, fill your atomizer with the material you'd like to vaporize.

Replace the magnetic top of your SOURCE orb 4.

Select Desired Airflow

Choose your desired airflow by twisting the Variable Airflow System (VAS) found in the middle of the orb.

Power On And Hit

Press and hold the Power Button to power and activate the atomizer.

Use the Left Option and Right Option buttons to decrease or increase the Wattage or Temperature until you reach desired settings.

Place your lips on the mouthpiece of the SOURCE orb 4, press and hold the Power Button, and inhale softly.

Release Power Button when done vaping, and take a few more cool hits to lower the temperature and any material left in the chamber.

Using Your SOURCE volt Max Battery

source volt max battery

How to Switch Modes On SOURCE volt Max Battery

The SOURCE volt Max has both temperature control mode and wattage moe that allows you full user control depending on your preference. To switch through these modes, press the Power Button 3 times in rapid sequence and the Top Mode row on the screen will begin to flash.

Press the Right Option button to switch to your desired mode: Power (to control wattage), Bypass (to get the full 60w power, not recommended for most atomizers), TCR (or Temperature Coefficient Resistance to control resistance of the atomizer, for advanced users), TEMP Ni, Ti and SS316 (for Temperature Control). 

Press the Power Button to select your desired Mode

Using your SOURCE volt Max in Wattage Mode

With your battery in Wattage Mode, use the Left Button or Right Button to increase or decrease your wattage.

Use the following Wattage settings depending on the atomizer used. Refer to this link for more information.

Once you have selected your desired wattage, you are ready to use your vape pen!

Using your SOURCE Volt Max in Temperature Control Mode

The SOURCE Volt Max offers 3 temperature control settings, depending on the type of coil used. To know more about what temp setting works with what 4 Series atomizer, please click on this link

Lock Resistance in Temp Control Modes

While in Temp Control Mode (Temp Ni/Temp Ti/Temp SS316/TCR), press the Power Button 3 times in rapid sequence until the Mode blinks.

Press the Left Option button twice to select the Resistance line (3rd line). It will blink.

Press the Right Option button to Lock or Unlock the current atomizer resistance.

When you see a Lock symbol, it is locked.

Note: Only Lock the resistance while in Room Temperature, this will lock in the base resistance of the atomizer. As long as the coil is not changed, you can remove the atomizer when hot and cold and the same settings will be saved, as long as a new coil is not installed.

If you install a new coil, reset your Resistance.

Change Wattage in Temp Control Modes

Change the initial Wattage in Temp Control modes for faster heat up times.

While in a Temp Control Mode (Temp Ni/Temp Ti/Temp SS316/TCR), press the Power Button sequentially 3 Times until the Mode blinks.

Press the Left Option button 1 time to select Wattage Line (2nd line). It will blink.

Press the Right Option button to raise the Wattage until you reach your desired setting.

Press the Power Button to lock in and select your Wattage.

Adjust User Info Display

Press the Power Button sequentially 3 times. The Mode will blink.

Press the Left Option button 3 times to select the User Info line (4th line). It will blink.

Press the Right Option button to switch between:

  • Puff: Total Number of Times Used
  • Time: Total Time Used in Seconds
  • AMP: Current battery Output.

To reset Puff and Time counters, please hold down the Power Button while either Puff or Time options are selected, whichever you'd like to reset.

How to Clean

To optimize the performance and prolong the lifespan of your SOURCE orb 4 and its atomizers, we recommend cleaning thoroughly whenever needed.

CLEANING YOUR ATOMIZERS

Atomizers are replaceable and disposable products that have to be changed every 4 to 6 weeks depending on care and use. To ensure that these products reach the specified time frame, we recommend cleaning AFTER every use to get rid of residue that may get stuck on the coils. To do this:

Make sure battery is not active and locked.

Unscrew the atomizer from the SOURCE orb 4 attachment.

For coiled atomizers

Submerge the atomizer a container with 91% isopropyl alcohol.

Shake softly for 3-5 minutes, and allow to air dry completely.

For coil-less atomizers

Use your dab tool to remove the top cap by unscrewing this counter-clockwise.

Remove the bucket and soak this in 91% isopropyl alcohol.

Shake softly for 3-5 minutes, and allow to air dry completely.

You can use a cotton bud dipped lightly in alcohol to gently wipe off material on the outer shell. 

CLEANING YOUR ORB ATTACHMENT

Take apart your SOURCE orb 4 attachment completely.

With a cloth lightly soaked in 91% isopropyl alcohol, scrub the SOURCE orb 4 attachment pieces to clean completely.

CLEANING YOUR BATTERY

Dip a cotton swab or cloth in 91% isopropyl alcohol, and clean the connection between the battery and the attachment regularly.

Keep this clean of sticky material, once it dries and it's connected to an attachment.

How to Charge

Charging your SOURCE volt Max

Unscrew your battery from the SOURCE orb 4 Attachment.

With the removable battery inside, plug your Micro USB cable to the front port of your SOURCE volt Max box mod. (Make sure it is dry and clean of any residue).

Plug your Micro USB charging cable into a wall charger.

The battery display on your screen will indicate a full charge after approximately 2 to 3 hours. 

Note: The removable battery is a disposable and replaceable product that lasts approximately one year. To check whether the removable battery needs to be replaced, try charging your box mod without this. If you see the charging icon functioning properly, it may be time to purchase a new removable battery. 

Charging your SOURCE orb 4 Premium battery

Unscrew your battery from the orb 4 attachment.

Check the inside of your battery connector and clean any debris or material with a cotton swab.

Screw your battery onto your 510 charging cable (Make sure it is dry and clean of any residue). The default light on the charger should be green.

Plug your charger into a wall charger.

Your battery will light up and your charger will light red while charging.

Your charger will turn solid green once fully charged (2-3 hours).